Showing posts with label tune up. Show all posts
Showing posts with label tune up. Show all posts

Sunday, October 04, 2015

Cat 3116 Tune Up Tools and Procedures


CAT 3116 Diesel Engine Tune Up from John Whelan on Vimeo.


Cat 3116 Injector Adjustment

The video shows how the Cat Tuneup Tool Kit works on a 3116 diesel engine. When the injector is installed I find it's easier to place the dial contact on the injector by feel and then having a look to make sure it's seated properly. In the Cat tune up kit you need the dial indicator, contact point, timing gauge block and magnetic base.

On top of the valve cover is a data plate that has the factory timing spec. This is the reading that you need to stick to when the timing tool is all set up. First of all you need to preset the dial indicator on the timing gauge block and set it exactly to 62.00 mm.

Rotate the engine so cylinder #1 is on the compression stroke. Both valves will be closed and cylinder #6 will be on the exhaust stroke. Injectors 3 5 6 can be set in this position along with 1 2 4 intake and 1 3 5 exhaust valves. (Intake .015 in exhaust .025 in) The injector spec on the valve cover can vary plus or minus .020 mm.

Rotate the engine 360 degrees and adjust the remaining valves and injectors. The Cat tool kit comes with a manual and gives you a detailed step by step procedure for these adjustments. It's a fussy operation but once everything is set these engines run very nicely. Keep the valve adjustment on a regular schedule because of a weakness in the exhaust valve stems that blow apart if there running at high temperature and rpms.

I hope the video gives you a better idea what's involved with injector set up on the 3116. The entire tune up kit is pricey and the last time I checked it was up around $4000.00 Canadian. We had to purchase it however that was in the mid 1990s and we paid much less than that. You can not get away with setting up these engines (except valve adjustment) without the kit.



Thursday, July 23, 2015

Cat 3116 Tune Up Steps



The 3116 Cat diesel engine tune up is quite involved because of the rack that controls the fuel injection system. The synchronization of the rack is the first step once the injectors are installed. The rack is mounted and torqued down on top of the head linked up to each injector rack.

The injectors must have hold downs installed on top of the return springs so the injector rack moves freely. The hold downs are included in the tune up kit. The #1 injector rack is non adjustable because it's calibrated at the factory. The tune up tools include a calibration fixture that has to be set up on #1 injector to enable the remaining 5 injectors to be synchronized.

After synchronization the full fuel setting is checked followed by injector timing and finally the valve setting. This is an extremely abbreviated explanation on setting up a Cat 3116 and without tools and some training it makes this job a tough one. The engine valve clearances can be checked but the rest definitely needs the tune up kit to complete the job properly.

Once going through the steps a couple of times setting these engines up it gets easier. Following the manual works it just takes time to get the calibration settings correct.

Saturday, October 10, 2009

Cat 3116 Diesel Engines

I've been getting a lot of questions on 3116 Cat Diesel Engine problems. The one stumbling block is the tooling you need to repair these model engines. After the basics like fuel supply and electrical issues are taken care of the next step is replacing injectors and other related tasks.

The tools required for tuning up these engines come in a kit and costs over $2000.00 in my part of the world. These tools must be used to get this engine synchronized, timed and set up properly.

If you have access to the tools that's great, a manual accompanies the kit. There is a learning curve with setting up the 3116 but do it once and you'll understand the concepts behind the injection system.


There are glitches with the 3116 are usually the same and I have posted them as they happened on this blog. The exhaust valves are weak and it seems like #5 exhaust valve is a weak spot. Keeping the valves set is a good practice and prevents a tight valve and overheating.

If you use the search box above you can get more details on tune ups and repairs. There are specific rebuild procedures covered as well.

Or you can check all the posts out here:

http://schoolbusmechanic.blogspot.com/search?q=cat+3116

You might have to be more specific with your search i.e "cat 3116 oil pump"

You can always make a comment or ask a question and I will get back to you...

Saturday, April 26, 2008

Avoiding Cummins Engine Repairs With Regular Tune-ups.

We recently had a Cummins Diesel Engine with a power complaint. One adjustment that gets overlooked is valve adjustment. This particular engine gained substantial power after adjusting the valves which required an average of 1/4 of a turn to meet specs. So this simple tune-up procedure should never be overlooked and must be carried out on regular basis.

The following is a valve adjustment on a Cummins ISB Diesel Engine: Valve adjustment on a Cummins Engine Repair is the final step. Engine position is very important because the intake and exhaust valves must be in the closed position.

Rotate the engine clockwise [looking from the front] until #6 cylinder rocker arms are both rocking. When you're on the correct stroke the exhaust valve will be moving into the closed position, then once it closes keep rotating the engine until the intake valve JUST starts to open. You are now on #1 Compression Stroke & ready to adjust 1/2 of the engine valves.

Note: The crossheads pictured here on top of the valve stems [#5 & #6 Cyl] are located with the elongated contact surface towards the exhaust manifold. The Rocker arms are held down on aluminum cradles with one retaining bolt and torqued to 27 ft. lbs.

Cummins 24 Valve Turbo Diesel Valve Adjustment Specs.

With the Engine on #1 Compression Stroke.

*Adjust #1 #2 #4 Intake Valves to .010 inch.

*Adjust #1 #3 #5 Exhaust Valves to .020 inch.

*Rotate Engine One Full Turn. #1 Cylinder Valves will rock like #6 did previously positioning the engine on #6 Compression Stroke.

*Adjust #3 #5 #6 Intake Valves.

*Adjust #2 #4 #6 Exhaust Valves.

I hope this mechanic information has helped you: It's not hard to adjust valves on a Cummins 24 Valve Turbo Diesel once you get the hang of it. All you have to know is how to position the engine correctly, the valve settings and some basic tools. That's it for now on Cummins Engine Repair.




Recommended: Diesel Engine Repair Manuals

Saturday, January 26, 2008

Cummins Engine Repair-Adjusting Valves ISB

  1. Valve adjustment on a Cummins Engine Repair is the final step. Engine position is very important because the intake and exhaust valves must be in the closed position.
Rotate the engine clockwise [looking from the front] until #6 cylinder rocker arms are both rocking. When you're on the correct stroke the exhaust valve will be moving into the closed position, then once it closes keep rotating the engine until the intake valve JUST starts to open. You are now on #1 Compression Stroke & ready to adjust 1/2 of the engine valves.

Note: The crossheads pictured here on top of the valve stems [#5 & #6 Cyl] are located with the elongated contact surface towards the exhaust manifold. The Rocker arms are held down on aluminum cradles with one retaining bolt and torqued to 27 ft. lbs.

Cummins 24 Valve Turbo Diesel Valve Adjustment Specs.

With the Engine on #1 Compression Stroke.

*Adjust #1 #2 #4 Intake Valves to .010 inch.

*Adjust #1 #3 #5 Exhaust Valves to .020 inch.

*Rotate Engine One Full Turn. #1 Cylinder Valves will rock like #6 did previously positioning the engine on #6 Compression Stroke.

*Adjust #3 #5 #6 Intake Valves.

*Adjust #2 #4 #6 Exhaust Valves.

It's not hard to adjust valves on a Cummins 24 Valve Turbo Diesel once you get the hang of it. All you have to know is how to position the engine correctly, the valve settings and some basic tools. That's it for now on Cummins Engine Repair.




Recommended: Diesel Engine Repair Manuals

Sunday, November 18, 2007

Cat 3116 Engine Synchronization Video Tutorial

Cat 3116 Diesel Engine Setting Synchronization is a multi-step operation and requires the Cat Tune up Kit. Some standard hand tools will work but most of the setting tools are specially designed for this purpose. NOTE: Remove fuel solenoid before starting synchronization, this allows free rack movement.

Below is Step One:

Calibrating #1 Injector




Step Two:

Setting Up For Injector Synchronization



Step Three:

How To Adjust Injector Synchronization



This is the hardest step to get around {especially for the first time} but comes much easier with repetition. The Cat 3116 Diesel Engine is a fussy engine to tune up but it pays you back with great performance.