Showing posts with label voltage. Show all posts
Showing posts with label voltage. Show all posts

Tuesday, June 16, 2009

Troubleshooting Electronic Diesel Engines



Troubleshooting electronic diesel engines can be a headache if you don't have the troubleshooting software required to check for codes. This is the first step when there is a amber or red code indicator light on the dash.

Once you rertrieve the code you can get a general idea what part of the electronic system to start focusing on. It may be a lost signal from a sensor or an innacurate signal that the computer (ECM) picked up.

Computers being as logical as they are will pick up on anything that is not within parameters according to the way they were programmed. This is a grreat advantage to your troubleshooting process.

Don't rule out the basics. A poor connection causing resistance will fool the ECM on the amount of resistance or voltage a sensor relays back to home. Always check connections both positive and ground starting at the battery.

There have been several instances in my shop where a poor ground has been the root of many electrical problems especially with electronic systems. So the first step is to check the electrical source thoroughly and then hook up the laptop.

If you send me a question about an electronic diesel engine with a code on the dash, I will tell you to follow the sequence in the above paragraph. It's reality now, every shop running or servicing electronic diesel engines need to have the proper software to get by with day to day operations.

Thursday, April 30, 2009

Diesel Engine Cranks Does Not Start

If a diesel engine cranks but does not start the first thing you want to look at is the power feed to the engine controls. In this case it's a Mercedes mbe 900 diesel engine in a 2007 conventional school bus. The first check is the fuse block since this powers up the ignition relays that operate the engine control modules.

Here is the Engine Power Distribution Module (photo below) with the relay that sends a signal to the engine control module.
The wavy line on circuit here has a ground to one side. With no ground the coil does not energize which will not allow the circuit to close.



Mercedes diesel engines have 2 modules, one on the engine and the other inside the cab. The ignition switch activates the relays that gives us the start operation. We found voltage to the cab module but when the engine was cranked over there was a voltage drop down to '0' Volts.

Tracing the wires and checking for continuity was the first step since a voltage drop means a resistance problem in one of the circuits. With the help of the Thomas Bus Tech Line we found the circuits to both relays then found the ground to be non-existent for both ignition relays.
These 2 ground wires (photo below) energize the coils within the relays. No grounds of course caused these relays to be become inactive.
After running a temporary ground the engine started. So obviously we had to check the ground connections on the firewall and the frame. After some digging there was a broken connector to a frame ground below the cab. Once repaired, the engine was back to normal once again.
The photo below shows the broken ground cable found just below the cab firewall on the outside of the frame rail.


This is Mechanical information that points out that a bad ground can cause a lot of electrical problems and should always be checked first starting at the batteries. A digital volt meter will tell you a lot with voltage and resistance readings. The higher the resistance the lower the amperage.

Saturday, February 23, 2008

Thomas Buses - Allison Transmission Wiring Modification

Thomas Buses are driven by an Allison MD 3000 Series Automatic transmission. This 1995 Saf-t-liner model had no power to the operators trans shift pad. The shift pad is also the Trans ECU [electronic control unit] so as I have said before always check the source , in this case the batteries.

There was a power feed open between the batteries and the rear control box at the engine compartment. I was able to limp the bus home by jumping battery power to the terminal board inside the control box which goes to directly to the operators cab supplying battery power to the shift pad/ECU.

This is obviously how I determined the open from the battery to the control box/terminal board [standard wiring on all Saf-t-liners]. The code for this fault is 35-00 [push both arrows on the shift pad at the same time with key on to retrieve code {under normal circumstances}

The control box at the engine compartment houses the engine intake heater components, lights etc. as well as the main battery power to the front electrical control box below the driver's side window.





My plan is to totally bypass the trans battery supply circuit from the battery to the ECU. Here you can see I've already cut the wires [larger #8 guage pos. and neg. wiring come from the battery while the smaller #10 guage pos. and neg. wires are running up front to the ECU]




This is the terminal board I mentioned earlier, factory wiring with spade connectors that connect the battery feed wiring to the trans. ECU wiring.

The first picture [top] shows the #8 pos. and neg. wires hooked up and running directly to the trans ECU. This will eliminate the extra #10 wires shown in the rear control box.


In the drivers cab the rear cover has been removed for easy access to the back of the trans. ECU. The upper plug can be removed and inspected for battery power. Both pos. and neg. #18 wires [2 each] run into this plug directly from the battery. The #8 wire is downsized under the dash to accommodate the smaller wiring into the ECU plug-in.



The 12V source from the battery is shown here with no connections in between. With a Digital Multimeter you can check for a battery voltage and a good ground.






So now you know when you have a shift pad with no reading [key on] the first thing to check is the battery voltage.

I hope this has helped you become more familiar with Thomas Buses equipped with Allison MD 3000 Series Automatic Transmissions.

Wednesday, January 02, 2008

Thomas Buses HDX Electrical Panel

Thomas Buses have changed through the years and one model with a different electrical layout is the HDX. This 2004 has everything in a totally different layout compared to the Saf-T-Liner.





The Body Electrical [lights and accessories] Schematic is nicely displayed on the side door panel below the driver's side window.

[Click On Each Photo To Enlarge]





The circuit board shown here has been unfastened and tipped downward so you can see the many connectors that hook up with relays and battery supply junctions. There are 3 circuit boards in total with specific spots for each connector.








The circuit board is upright once again [located in the side panel] Here you can see the main battery power supply on the left with the many fuses and relays required to run lights, heater motors, solenoids etc.
The LED lights above indicate which relays are active, YELLOW
indicates the relay coil has been activated while the GREEN LED indicates the circuit is connected to the load.

Thomas Buses have evolved from the basic "battery to load with a switch in between" to complex relays & mult-functional switches that handle the demand for more circuits that can meet the load & safety component demands of today's School Buses.

Wednesday, December 19, 2007

Charging System Test - Heavy Duty 12 Volt System

A charging system test is a very basic operation with the right tools. Pictured is a Leece Neville 160 Amp Alternator which works very hard to keep the three 900 CCA [Cold Cranking Amps] bus batteries charged. Thomas School buses have a large demand with extra lights, electric motors and the engine air intake heater. The diesel engine in this case is a Cummins ISC Electronically controlled unit.



You're probably wondering what the heck is that device hooked up to the batteries? That's my tool of choice, a 'SUN' VAT 33 [Volt Amp Tester]. This model has been around for decades and still very reliable, our shop does have a digital tester but I like this one for doing a quick check on the charging system. The reason I'm testing the charging system is because of an unusually low voltmeter & ammeter reading.




The main leads are hooked up to the positive and negative battery terminals while the amps pickup is clamped around the positive cable to read alternator ouput back into the batteries. The engine must be running at high idle [approx. 1200 rpm]

The black control knob I'm turning puts a load on the batteries which should kick in the alternator to charge very close to maximum. Once I bring down the system voltage to 12V the alternator should normally put out a full charge of approx. 160 amps.

The test revealed the alternator is only putting out 80 amps maximum which will not keep up to the demands of a fully operational school bus & must be repaired or replaced.

This is a fast and easy way to do a charging system test on a 12 Volt Heavy Duty charging system.

Click here to sell your car online at eBay!

Saturday, December 15, 2007

Thomas Buses-HDX Electrical System Repair

The electrical system on Thomas Buses vary depending on the model, pictured is an HDX model built in 2004. We are going to change a module that controls the main power to the body and chassis electrical systems. A hoist is handy but not totally required, I had to enlist a grinder with a cut-off wheel to remove the existing bolts.





This unit is called a dual power switch that is mounted on the frame on the passenger side across from the transmission. Since it is exposed to the elements the terminals are exposed so corrosion can develop. Consequently their is a possibility of an intermittent power problem to the lights or engine/trans controls when turning on the ignition.





As you can see the middle terminal is connected directly to the main batteries. The chassis and body battery supply terminals are located on each side while the ignition feed connector is plugged in on the top left corner.
When the ignition is energized a signal is sent to this module and power is directed to both systems. The chassis is the engine, trans. and running electrical while the body electrical is the lighting system.


Here is the module installed on the frame with four fasteners and an insulator between the module and the frame surface. It depends totally on what kind of environment you drive in for a problem to occur with this component. It is very well sealed internally with a hard epoxy type substance.
I hope this article has enlightened you with what to look for when experiencing electrical problems with Thomas Buses.

Sunday, October 14, 2007

Allison Automatic Transmission Wiring & Troubleshooting

The Allison Transmission Control Unit on the 1999 Saf-T-Liner is located under the floor directly below the driver. There are 3 plug-ins which is an easy way to tell this is a W-TEC 3 system [World Transmission Electronic Unit 3rd generation]. The Transmission vehicle speed signal enters here and exits at two different plugs, one for the speedometer and the other to the Cummins ISC ECU.



We will trace the exiting wire from the ECU that provides our Vehicle Speed Signal since that is the code and the speedometer is operating normally. Since we have speedo operation that gives us an obvious clue that the incoming signal to the Trans ECU is OK.[resistance should be checked regardless]
The wire we want to trace goes from the Trans ECU to the VIM [Vehicle Interface Module]
Removing the dash back cover makes this check MUCH easier.


Remove the cover from the VIM








The VIM is an interface between the Trans ECU and the chasis wiring. Various operations are accomplished through this module like the exhaust brake, back up lights, neutral start, high idle and of course our vehicle speed signal runs through here to the Engine ECU.
[Click the Pic to Enlarge]
Now we can check the continuity and see if we have a circuit. After checking this out there is no connection between the Trans. ECU and the VIM.
I'll run a new wire to repair the open circuit, an easy fix. It's nice to get a gimme once in awhile!

In the VIM you'll notice a series of relays and 2 fuses. If you experience a dead keypad and there is battery voltage to the VIM then check these fuses. One is main power & the other is ignition power.



The other vehicle speed signal wire [tan wire # 157] comes from the trans ECU directly to the speedo. The speed signal to the VIM is the same number [tan wire #157] since it comes from a different plug.




This is where it all begins from the output shaft housing of the transmission. The output sensor is a single coil unit that sends an AC voltage to the Trans ECU.
There is a toothed wheel rotating inside the housing that creates the signal to the sensor.
The Allison 3000 Automatic Transmission is a very reliable unit when maintained properly. The wiring problems come and go but are easy to trace and repair with the right tools and wiring diagrams.

Friday, September 28, 2007

Basic Electricity How It Works

Basic Electricity applies to any type of machinery running on a 12 Volt Direct Current system. Once you see how it works it's much easier to understand, instead of making it complicated I will explain the basics in layman's terms. This is the chasis electrical panel on a 1995 Thomas Saf-T-Liner[pusher]. note: Click on the Photos to Enlarge
It looks a lot more complicated than it really is. Any 12 Volt electrical system has a source of power from the batteries, in this case we run on 3 top post 900 CCA [cold cranking amp rated] batteries.

That's a lot of juice available to supply voltage to the body and chasis circuits, but there are environmental and mechanical factors that will cause a severe voltage drop if not detected.

Voltage is like a river, the heavier the flow the stronger the current. If there's a dam down river this will cause resistance and restrict the flow. If the source [the river] is cut off so is the flow.

Any resistance between the battery and the load will cause a voltage drop, this can be caused by a short circuit, open circuit or just plain resistance from corrosion. A good rule of thumb when troubleshooting a 12 volt circuit is to:

Step 1...Check the battery -Sufficient Voltage?
Step 2...Check the load i.e. A Light or Relay, is it working?
Step 3...Check the connections
Step 4...Check the wiring

Very basic steps but most electrical problems are found using these steps, check the simple things first.

Say for instance you have 13.5 volts at the battery and 0.0 volts at the load. This means you have an obvious Open Circuit problem [a rubbed through wire possibly]

Using a digital ohmmeter you can ground one end of the circuit and using the two ohmmeter leads at the other end connect one lead to the faulty wire and the other end to ground. What you're doing here is checking for Continuity [the ohmmeter has it's own battery voltage which runs through the faulty wire].

By the way, the multi-meter you use for newer equipment must be Digital to safeguard the electronic systems that are much more common in new trucks and buses. If the circuit breaker is popping on and off then there is obviously a Short Circuit which can be hunted down using a Short Finder [a very slick tool to have which saves a lot of time and grief]

You hook up the auto-reset breaker then slide the meter along the wiring until it finds the exact spot where the short is [the indicator needle stops moving] along the frame or body.
Clean the connections and check the load i.e. marker light or tail light for poor grounds & connections.
That's a Quick Overview on Troubleshooting a Basic 12 Volt Electrical Circuit.

Wednesday, September 26, 2007

Testing Automotive & Heavy Duty Batteries

Here's a great video on testing a battery using the proper battery tester . There are many different battery testing models and they all work, all you want to accomplish is to put a load on the battery and read the voltage level. You need to know the CCA [cold cranking amp] rating labeled on top of the battery, then draw 50% of that off the battery with your tester for 10 - 15 seconds [the tester has a carbon pile that absorbs the heat from the heavy draw].

A general rule of thumb I use is a battery voltage drop of no less than 9.6 Volts after a 10 second load of 50% of the Cold Cranking Amp Rating. One important factor is the battery must be fully charged before testing, preferably around 12.6 Volts.

A battery tester is affordable but if you don't own one & you're not sure of the condition of your battery then a quick load test at a repair shop is worth it. A reputable shop won't charge you for the test if you buy a battery from them [since the test only takes less than a minute from start to finish].